2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer
2K DTM High Build Primer

2K DTM High Build Primer

$35.00 Save $-35.00
29 in stock

Description:

Custom Paints Direct to Metal (DTM) Primer. VOC 2.1
2K DTM Primer-Surfacer with exceptionally high build and direct-to-metal properties. Very soft sanding, wet or dry after short dry times. 2K DTM Primer provides no shrinkage and the maximum in color holdout properties available.


Available in 3 colors: grey, white and black which can be blended to make different shades of grey. Suitable for: Car, Motor bike, Caravan, Commercial Vehicle and industrial industry. TYPICAL SUBSTRATES: ▪ OEM primer ▪ GRP / fibreglass ▪ Epoxy primer surfacer ▪ Polyester putties ▪ Existing finishes in good condition ▪ Etch primer

Substrates:

2K DTM High Build Primer can be used on the following substrates

  • Metal
  • Galvanized
  • Aluminium
  • OEM primer
  • GRP / Fiberglass
  • Body Filler
  • Polyester putties

Mixing:

The mixing ratio for 2K DTM High Build Primer:

  • 4 parts 2K DTM High Build Primer
  • 1 part DTM Activator

The mixing ratio for 2K DTM Sealer:

  • 4 parts 2K DTM High Build Primer
  • 1 part DTM Activator
  • 1 Part 2K Reducer

2K DTM Primer includes:

2K High Build Primer 1 Quart:

  • 1 Quart High Build Primer.
  • 1/2  Pint Activator.

2K High Build Primer 1 Gallon:

  • 1 Gallon 2K DTM High Build Primer.
  • 1 Quart DTM Activator.

SURFACE PREPARATION:

Clean and dry the surface. Sand surface with P220—P380 grit abrasive.


MIXING:

4 Parts 2k DTM Primer  
1 Part Activator 
Reduction of up to 10-15% with Urethane reducers


OPTIONAL MIX 4:1:1 as a SEALER (4 parts primer 1 part Activator, 1 part 2K reducer)


POT LIFE 1 Hour @ 70°F (20°C)


GUN SET UP:


Conventional
Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)


HVLP
Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)
Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”)


Air Pressures
Conventional
Siphon Feed: 35-45 psi at the gun
Gravity Feed: 30-40 psi at the gun
HVLP 8-10 psi at the gun


APPLICATION:


Clean surface thoroughly using accepted body shop procedures. Sand per accepted body shop procedures for substrate being used and final clean with solvent wipe. Apply 2-3 medium coats of 2K DTM Primer with 10-15 minutes flash between coats. Do not apply more primer after 1 hour from completion.

FLASH TIME/DRY TIMES @ 72ºF / 22.2ºC:
Flash/Dry Times (Air Dry):
Flash Between Coats: 10-15 minutes
Wet Sanding: 1 hour
Dry Sanding: 1 hour
INFRA RED 15-20 minutes


Times can vary depending on the air temperature and air movement.

 
RE-COAT: Topcoat within 24 hours of sanding. If time exceeds 24 hours, the primed surface must be sanded and cleaned again prior to application of primer or topcoat.


SANDING: Dry & D.A.: P400—P600 Wet Sanding: P500—P600

2K DTM Primer Kit includes:

2K High Build Primer 1 Quart Kit:

  • 1 Quart High Build Primer.
  • 1/2  Pint Activator.
  • 1/2 Pint 2K Reducer

2K High Build Primer 1 Gallon Kit:

  • 1 Gallon 2K DTM High Build Primer.
  • 1 Quart DTM Activator.
  • 1 Quart 2K Reducer 

 

    Back to All Products